 |
FAQ |  |
Frequently Asked Questions
|
FAQ | |
Frequently Asked Questions
A: Polished Nail Systems has the very best retention because of the liquid/powder ratio. 90% of lifting problems are caused from improper preparation or use. Seven sins that cause lifting:
|
|
A: Two ways to remedy this. One, rough up the nail, prime, and add more product. Two, simply add a coat of matching nail polish. The longer you use Polished Nail Systems the less likely this will happen. If the white shows through on the sides or the free edge try: One, shorten the nail to fix the free edge. Simply bevel underneath the free edge of the nail. Two, leave the tips a little longer when you first begin using Polished Nail Systems, so that you can shorten the free edge afterwards if necessary. Three, it is a good idea to look at each nail after the acrylic dries. If there is any area where the acrylic is thin you will see an inconsistency in color and can add more acrylic thus preventing filing through. Remember, Polished Nail Systems is a softer product and requires a softer file and less pressure when filing.
Q: Sometimes when I'm sculpting the product looks gritty and is hard to work with. Why?
A: You are definitely sculpting too dry. Make sure the product looks glossy and shiny during application. When it dries it will look gritty and velvety.
Q: When I set my balls of acrylic down liquid seems to flood the rest of the nail and runs into the cuticle which I know can cause allergies to acrylic over a period of time.
A: This is almost always caused from cleaning your brush in acetone or brush cleaner. These chemicals will dry out the brush hairs and then the brush will not hold liquid properly. Since Polished Nail Systems is not self-leveling a good brush is absolutely necessary to control the product; Clean your brush with liquid monomer only.
Q: What about fungus and mold?
A: A fungus problem usually starts with an injury or harsh chemicals under the nail plate at the free edge, creating a pocket in which the fungus can develop. It grows through the nail, turning black/green when reaching the top. Filing will not kill it, This type of problem must be looked at by a doctor. Yeast is perhaps the most common. The free edge pulls away from the plate, and if not checked can continue to the matrix area. Mold can happen anywhere moisture collects. On a nail this can happen with anything from nail polish to acrylic. When this environment sets up, this bacteria will begin to grow in the moisture on the nail, looking greenish in color. Once the moisture is removed and the natural nail is sanitized, the bacteria is gone (although the greenish stain may remain). Dehydration and clean application will help. Polished Nail Systems should not be filled in continuously for a long period of time. Polished Nail Systems should be removed periodically to check the natural nail. Educate your client! Provide them with Polished Nail Systems client information sheet on caring for and maintaining their nails. This will prevent most problems before they start.
Q: What can I do when I want a color change between sets?
A: If you like to change polish often, start with a lighter color because it is easier to cover. Simply cover with four coats of polish, since most women stay in the same color tone, usually one coat of polish will create a new color. Color changes can be made easily when performing fill-ins. See instructions under color changes.
Q: Sometimes I get tiny white spots on the nail when I am buffing.
A: These are tiny air bubbles that cannot be seen as easily with natural powders or French manicure lines. There are two things you can do to prevent this: One, sculpt wetter. Two, buff with oil (this will get the white dust out of tiny holes). Then apply a top coat.
Q: Why is it necessary to remove nails periodically?
A: To maintain healthy, problem-free nails! This allows checking the natural nail and replaces acrylic that has been damaged (by UV rays, water, chemicals, and normal wear-and-tear). Remember new nails are the most durable service you can offer a client.
Q: What is the best way to remove a set when a soak-off is necessary?
A: Polished Nail Systems is very easy to soak off. Properly done, it should take only 10-15 minutes. Since this is only done once every 6-8 weeks, this is actually much less salon time spent than drying polish weekly or bi-weekly.
|
THE QUICK AND EASY SOAK-OFF
KEY: DO NOT TAKE THE HANDS IN AND OUT OF ACETONE |
A: Yes, acetone can be extremely drying. Since harsh chemicals can damage the delicate skin around and under the nails, we suggest using petroleum jelly, under the nail plate, at the free edge and around fingers.
Q: How do we get a high gloss when buffing?
A: Make sure not to graduate too quickly from a 180 file to the white block. Try using the white block buffer a little longer than seems necessary. Be sure to wipe all grit and dust from the nail and the 3-way buffer, as even the smallest amount of dust will prevent a high gloss. Cuticle oil may be helpful.
Q: What if my polish doesn't match the acrylic exactly? Will each new jar of powder be exactly the same shade?
A: There may be a slight color variation from batch to batch. Allow the polish to dry completely before you decide it doesn't match. The polish should give you a good idea of what color the acrylic will be, and enable you to do light touch-ups. One coat of polish over the colored acrylic will not look exactly the same as two coats of polish over the natural nail.
Q: What if my liquid gets gummy?
A: This means you are not wiping your brush off thoroughly. Try wiping your brush after you finish sculpting each ball of product. Then dip into the liquid and wipe again before continuing to the next ball. Do not wipe your brush during application of anyone ball of product. This will cause you to sculpt too dry. Do not try to sculpt with liquid that is gummy. This will cause lifting.
Q: Sometimes the powders do not look consistent in color.
A: This is not unusual, if the powder has set for a while. Simply shake the powder before use!
